그런데 arcconf 설치 후에 GENCONFIG를 보니 아래와 같네요.
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Channel description : SAS/SATA
Controller Model : Adaptec 5805
Controller Serial Number : 0D461183C91
Physical Slot : 16
Temperature : 49 C/ 120 F (Normal)
Installed memory : 512 MB
Copyback : Disabled
Background consistency check : Enabled
Automatic Failover : Enabled
Global task priority : High
Performance Mode : Default/Dynamic
Stayawake period : Disabled
Spinup limit internal drives : 0
Spinup limit external drives : 0
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/1
SSDs assigned to MaxCache pool : 0
Maximum SSDs allowed in MaxCache pool : 8
MaxCache Read Cache Pool Size : 0.000 GB
MaxCache flush and fetch rate : 0
MaxCache Read, Write Balance Factor : 3,1
NCQ status : Enabled
Statistics data collection mode : Enabled
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 5.2-0 (18948)
Firmware : 5.2-0 (18948)
Driver : 1.2-0 (30200)
Boot Flash : 5.2-0 (18948)
--------------------------------------------------------
Controller Battery Information
--------------------------------------------------------
Status : Not Installed
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : JSHYSB1
RAID level : 6 Reed-Solomon
Status of logical device : Suboptimal, Fault Tolerant
Size : 17141750 MB
Stripe-unit size : 128 KB
Read-cache mode : Enabled
MaxCache preferred read cache setting : Enabled
MaxCache read cache setting : Disabled
Write-cache mode : Disabled (write-through)
Write-cache setting : Disabled (write-through)
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Segment 0 : Present (Controller:1,Connector:0,Device:0) W1F4JWSY
Segment 1 : Present (Controller:1,Connector:0,Device:1) W1F4K2JQ
Segment 2 : Rebuilding (Controller:1,Connector:0,Device:2) W1F4JWWY
Segment 3 : Present (Controller:1,Connector:0,Device:3) W1F4JXLC
Segment 4 : Present (Controller:1,Connector:1,Device:0) W1F4JXS9
Segment 5 : Present (Controller:1,Connector:1,Device:1) W1F4K3JD
Segment 6 : Present (Controller:1,Connector:1,Device:2) W1F4K3FP
Segment 7 : Present (Controller:1,Connector:1,Device:3) W1F4K2FS
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,0(0:0)
Reported Location : Connector 0, Device 0
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4JWSY
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #1
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,1(1:0)
Reported Location : Connector 0, Device 1
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4K2JQ
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #2
Device is a Hard drive
State : Rebuilding
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,2(2:0)
Reported Location : Connector 0, Device 2
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4JWWY
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #3
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,3(3:0)
Reported Location : Connector 0, Device 3
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4JXLC
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #4
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,4(4:0)
Reported Location : Connector 1, Device 0
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4JXS9
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #5
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,5(5:0)
Reported Location : Connector 1, Device 1
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4K3JD
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #6
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,6(6:0)
Reported Location : Connector 1, Device 2
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4K3FP
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
Device #7
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,7(7:0)
Reported Location : Connector 1, Device 3
Vendor :
Model : ST3000DM001-1CH1
Firmware : CC29
Serial number : W1F4K2FS
Size : 2861588 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off,Reduced rpm
SSD : No
MaxCache Capable : No
MaxCache Assigned : No
NCQ status : Enabled
실은 처음에 array 하나 빌딩 후에 테스트 삼아서 하드 하나를 뽑아봤더랬지요..
강렬한 비프음과 함께 오류 보고가 되고 suboptimal 로 바뀌는 상황을 보고, 다시 하드를 끼워넣어 리빌딩 되는걸 보고
잘 돌아가는 구나 싶어 흐뭇했는데, 첫번째 하드 리빌딩이 끝나자마다 다른 하드 하나가 S.M.A.R.T fail 보고가 되면서 다시 비프음 발생.. 현재 재부팅해서 리빌딩 중입니다. 식겁했습니다. :(
그래서 S.M.A.R.T 가 no 라 찍히는게 무슨 연관이 있나 싶어 질문드려봅니다.
전에 이선호님께서 seagate 하드는 SATA 3G 로 점퍼 세팅을 하라 하셨는데 점퍼 세팅이 어떤지 뒤져도 안나오고 구매할때 점퍼도 안들어있어서 그냥 끼웠는데 그 문제도 마음에 걸리구요.
하드디스크 점퍼는 따로 팔지 않습니다.
(조금 구하기 힘듭니다. 고객지원센터에 문의하여 보세요.)